Lite-Weight gypsum drywall provides all of the strength and sag resistance found in our regular drywall, but it is as much as 30% lighter than typical gypsum ceiling boards. The ½”-thick panels are available in both 48” and 54” widths and a variety of lengths from 8’ to 16’. Designed to cover walls and ceilings, they can be installed over wood or metal framing spaced up to 24 o.c. This versatility makes Lite-Weight gypsum drywall the only drywall you need for a range of remodels, new residential and light commercial projects. And with the reduced weight comes less physical fatigue, allowing installers to be more productive each day.
Features:
- As much as 20% lighter than typical gypsum ceiling board
- Strong, sag-resistant panels may be installed on walls and ceilings with wood or metal framing up to 24” o.c.
- Long tapered edges make joints easier to finish and conceal
- SCS-Certified 97% recycled content contributes toward green building certifications
Product Specifications:
| | Federal Specification
SS-L-30D | Product Standard
ASTM | Installation Standards |
|---|
| 1/2" (12.7 mm) |
Type III & Grade R | C1396 |
ASTM C840, GA216, GA214 |
| Properties |
48" (1219 mm) Width |
54" (1371 mm) Width |
| Thickness |
1/2" (12.7 mm) |
1/2" (12.7 mm) |
| Lengths |
8' (2438 mm)
9' (2743 mm)
10' (3048 mm)
12' (3658 mm)
14' (4267 mm)
16' (4876 mm)
|
12' (3658 mm)
14' (4267 mm)
16' (4876 mm) |
| Edge |
Tapered |
Tapered |
| Product Standards |
IBC, ASTM C1396 |
IBC, ASTM C1396 |
| Application Standards |
ASTM C840, GA216 |
ASTM C840, GA216 |
| Weight (lbs./sq. ft.) |
1.384 pfs |
1.384 pfs |
Special Order Information:
Other widths, edges and lengths may be available on special order with established minimums and lead time. Some products may not be available in all markets. Please check with your local Temple-Inland sales representative.
Limitations:
- Designed for interior, non-fire-rated assemblies only
- Avoid exposure to temperatures in excess of 125°F (52°C)
- Avoid exposure to excessive or continuous moisture
- Must be protected from direct exposure to weather and properly supported to prevent sag
- Maximum framing spacing on walls and ceilings is 24” o.c. and must be installed perpendicular to framing
- Maximum insulation load: 1.3 psf with 24” o.c. framing, 2.2 psf with 16” o.c. framing
- Should be stored, handled and installed to comply with industry standards ASTM C840 and GA216
Low VOC-Emitting Material:
Temple-Inland gypsum board products are third-party certified by Materials Analytical Services, LLC (MAS) to meet the performance standard established for low-emitting materials under the Collaborative for High Performance Schools (CHPS) Program.
Sulfur Emissions Testing:
In emissions level testing for carbon disulfide and carbonyl sulfide conducted by Materials Analytical Services (MAS), Temple-Inland gypsum board was determined to be negative for sulfur off-gassing and is not considered a problematic corrosive drywall type.
Storage:
Lite-Weight gypsum drywall should be carried, never dragged, to prevent damaging the finished edges and surfaces. Store gypsum boards lying flat and neatly stacked, off of the ground, and indoor or under roof to protect them from weather and direct sunlight. Care should be taken to prevent sagging or damage to edges, ends and surfaces. Leaning boards against framing is not recommended.
