Specify TemStock-MR for cabinets and fixtures with an elevated risk of exposure to liquids and high humidity. Featuring enhanced moisture-resistant resins and other additives, TemStock-MR is formulated to provide increased protection without sacrificing performance. It can be machined, drilled and laminated with premium results.
Dimensions
| Thickness (in.) | 1/4 - 1-1/8 |
| Panel Sizes (in.) countertops and shelving available |
49 & 61 x 73-169 |
Properties
| Averages1 | 3/8" to 1/2" | > 1/2" to < 1" | ≥ 1 |
|---|---|---|---|
| MOR-Modulus of Rupture (psi) | 1885 | 1885 | 1885 |
| MOE-Modulus of Elasticity (kpsi) | 290.1 | 290.1 | 290.1 |
| IB-Internal Bond (psi) | 90 | 80 | 75 |
| Face Screwholding Capacity (lbs) | 202 | 202 | 202 |
| Edge Screwholding Capacity (lbs) | NA | 1802 | 180 |
| Formaldehyde Emission (ppm)3 | 0.09 | 0.09 | 0.09 |
| 24-Hour Thickness Swell4 | 7.0% | 4.0% | 4.0% |
| 1. One-panel minimum average (ASTM D1037 / ANSI A208.1-2009) 2. 5/8" and thicker 3. Maximum value 4. One-panel maximum average (ASTM D1037 / ANSI A208.1-2009) |
|||
Tolerances
| Length & Width Tolerance | ± 1/16" |
| Squareness Tolerance | ≤ 1/8" |
| Straightness Tolerance | ± 1/64" / 2ft. |
| Thickness Tolerance (Within Panel Average) |
± 0.004" |
| Thickness Tolerance (Panel to Panel Average) |
± 0.004" |
Environmental Credits
| LEED | Credits | Description |
|---|---|---|
| Recycled Content | MR credit 4 | Awards 1 or 2 points for using products with recycled content that constitute at least 10% or 20%, based on cost, of the total value of project materials. |
| Locally Produced Materials | MR credit 5 | Awards 1 or 2 points for using materials on a project that are extracted and manufactured within 500 miles that constitute at least 10% or 20%, based on cost, of the total value of project materials. |
| NAHB | Credits | Description |
|---|---|---|
| Pre-Consumer Recycled Content | 604.1(2) | Use recycled content products in major areas such as walls, floor, insulation and roofing |
| FSC® Certification | 606.2(3) | Wood or wood-based products available that are certified by Forest Stewardship Council™ |
| Other Certification | 606.2(6) | Wood-based components certified in accordance to CPA-EPP |
| Low Formaldehyde/VOC emissions | 901.4(a) | In compliance with ANSI A208.1 |
| Low Formaldehyde/VOC emissions | 901.4(c) | In compliance with EPP-CPA 3-08 |
| CARB | Credits | Description |
|---|---|---|
| California Air Resource Board | C.A.R.B. | Approved NAF exemption, exceeding requirements of CARB, Phase 2 |
Recycled Content Certification:
The particleboard produced in Temple-Inland’s Monroeville, Alabama, Hope, Arkansas, Thomson, Georgia, and Diboll, Texas facilities has been certified by the Composite Panel Association as complying to their Environmentally Preferable Product (EPP) specification standard CPA 3-08 to contain 100% recycled and/or recovered fibers.
In addition, this certification verifies Temple-Inland particleboard products conform to both ANSI A208.1 Table B and HUD CFR Part 3280 Formaldehyde Emission Requirements.
Particleboard produced at Temple-Inland's Monroeville, Alabama, Hope, Arkansas, Thomson, Georgia, and Diboll, Texas, facilities that is certified to conform to the requirements of Forest Stewardship Council™ standards for Chain of Custody, Controlled Wood and Reclaimed Material manufacturing is available by special order.
Warning
This particleboard contains low fuming urea formaldehyde resin and may release formaldehyde vapors in low concentrations. Formaldehyde vapors can be potentially irritating to the eyes and upper respiratory system. Should irritation develop, consult your physician.